Covering midbass pods with cloth

     In this post I will describe steps that I have done to build cover-ups for midbass speakers in my car. Here you can see how I made midbass speaker pods in the front doors of my car. As you can see, these pods look awful although they are very useful for any car audio installation. In this post I'll try to make them less ugly not to say "good looking". :)

     Since I have some minor experience working with fiberglass, it was decided, that the covers for pods will be made out of fiberglass because you can get whatever forms you like. The technology or the way to make them can be very different. It depends on the door trim itself, your skills and desire to ruin few days of your life. Different styles can bee seen on the Internet. If you want to have interior of the car as original as it could be, it is possible to have the pods be built in the door trim so it looks like factory made. It requires a lot of skills, material and fabrics selection etc.

      I went the easy way. 

     The first step is to take food film, fold it in several layers and attach that film over the speaker pod. You should align the film on every curve and edge of the pod. The film it self can be fixated with some paper tape or something that wouldn't allow the film to move out of the correct position. This is done to protect the door trim from resin that will be used to glue fiberglass while replicating curves and form of the pod.

     Unfortunately I didn't take a picture of this process. But I think you get the idea. Be extra careful to cover all of the pod and its surroundings, because if the resin (glue) will touch the door trim, you won't be able to clean it off.

     The next step is to apply glue (resin) and fiberglass squares so you would have fiberglass form of the speaker pod. I have described in details how to handle fiberglass and resin, so I won't do it again. You can look for older posts in this blog. If you are very talanted, you might apply fiberglass with one try and get the perfect form. I wasn't, so I was prepared to apply another layer of fiberglass afterwards.

     After few hours or minutes (depending on the proportions of resin vs hardener) you can peal off the food film with fiberglass cover and cut off the excess fiberglass.

This is how it looked for me:

       

      As you can see, it is far from perfect. But with the next layers of fiberglass I made the form to look as it should be (in my opinion).

     

      After I got the form right, it was time to cover it with cloth.
      I chose Alcantara "wannabe" cloth (something like suede).
      In this step I will not go in to details as it is described in my previous posts (Tweeter podiums).
     The only difference is with the stitching where cloth made wrinkles. Covering tweeter pods I sew cloth peaces together. This time I used only glue. And it turned out better then I suspected. 

After that speaker pod cover was attached to the wooden ring fo the speaker pod with few screws.

Midrange speaker pods: step #2

   The doors at this point are packed with vibroisolation, so it's time to start creating pods.

Creating structure for pods is a creative thing. There are a lot of different solutions and types of construction. You just have to use imagination. It is only important that these pods would be stable, they wouldn't wobble around and they would be joined with the doors, so - construction should be rigid.

I used small wooden bricks as you will see in the pictures below.

    The first problem I encountered is that the door panel/trim is thick so speaker ring (wooden ring on which speaker will be attached) must be quite far from the door structure. Since I didn't had very long screws that would go from wooden speaker ring to the door structure I had to improvise. 

I'll try to sketch what I have done:

    This, of course, is not the best way to create distance between doors and speaker ring, but it did the trick for me. This construction was stable and rigid.
    To create the above construction first of all you have to cut a hole in the door panel where the pod will be. I cut the panel with jigsaw. The hole in panel is needed to measure what will be the distance between door structure and speaker ring. As you can see in the picture below, I have cut hole in the door panel and attached few wooden bricks (not enough).

    After attaching few extra wooden bricks until appropriate distance has been achieved, speaker ring has to be attached.
    The speaker ring should be placed in such angle that speaker would point to the gearbox leaver.

    Next step is to cover this construction with vibroisolation so it would be hermetical (keep in mind that it is impossible to make it airtight - just do your best).

    Then attach the speaker (don't forget to connect the wires... :) ).

   It would be best to apply some silicone between wooden ring and speaker (if the speaker doesn't have rubber ring).

    

In addition I would suggest to put some cloth between doors and door panel. Because panel is made from plastics and the aluminum foil is not very elastic. Since this speaker will produce a lot of vibration, layer of cloth between door and its panel will reduce additional unwanted noises. 

   At this point I haven't created decorative trim for the pods. I'll try to work on them this summer using fiberglass. This will be very difficult task, but interesting and useful.